Category: PRO XP

PRO XP

Showing all 39 results

  • Tree Kicker Bolt Kit

    $40.00$150.00

    This tree kicker bolt kit is for 2 or 4 seater L&W tree kickers. 

    (1K/TURBO/TURBO-S) 2 seater set comes with 4 L bolts.

    (1K/TURBO/TURBO-S) 4 seater set comes with 6 L bolts.

    (PRO XP) 2 seater set comes with 6 frame pins. 

    (PRO XP) 4 seater set comes with 8 frame pins.

    This is just a replacement kit. 

    For new tree kickers, click the link below. 

     

    If you are looking for new tree kickers please click here- https://landwfab.com/?s=TREE+KICKERS&product_cat=0&post_type=product

    http://facebook.com/landwfab

    Select options
  • Keller Ball Joint

    $130.00$510.00

    If you are needing ball joints for a full set (4) of A Arms, please choose a set of 4. 

    If you are needing them for Uppers, choose a set of 2. 

    If you are needing them for Lowers, choose a set of 2.

     

    The Mega Ball Joints are used for our mega ball joint a arms. The will not fit a regular a arm.

    These ball joints are for rzr only (XP, TURBO, RS1, PRO XP, TURBO S). They do not fit a general or Ranger. 

     These ball joints have a hardened body and stem. Stem is built from AMERICAN made 4340 and hardened for maximum strength and wear resistance. Adjustable and greaseable with a replaceable boot.

    Select options
  • PRO XP Tie Rods

    $189.00$325.00

    These tie rods are for the Pro XP.

    They have a lifetime warranty. 

    Factory ends are not warrantied, only the tie rod itself. 

    *PLEASE NOTE: If running 14″ wheels, the tie rod will make contact with the wheel at full turn. You can avoid this by running a wheel spacer or a steering stop. 

    Specs for HD Rebuild-able Tie Rod Ends:

    Fully rebuild-able

    Comes assembled with grease ready for installation Compatible with all L&W tie rods plus many others Starts with heat treated 4140 Black oxide finished

    100 percent made in USA

    This product holds an 18 month warranty

     

    https://www.facebook.com/landwfab/

    Select options
  • PRO XP- 2 Heim Radius Rods

    $240.00$465.00

    THIS LISTING IS FOR PRO XP MODELS ONLY.

    The lowers are High clearance and always come Direct Bolt.

    The 2 Heim Uppers come with both a Left and Right Hand heim on each end of the rod for adjustability if needed. 

    *Adjustable uppers are usually necessary to correct any camber issues that you may have or experience on your machine.  Most times if you plan to change tender springs, or if you are running a bigger set up (portals, lifts, changing ride height most times will cause +/- camber that you will need to correct with adjustable uppers.) 

    Includes all misalignment spacers needed for install. 

    They are 6061 Aluminum, and made in the USA. 

    These Radius Rods hold a Lifetime Warranty.

    Select options
  • L&W Rear Inner Fender Mud Guard- PRO XP/ TURBO R

    $65.00

    FOR PRO XP/ TURBO R MODELS ONLY!

    This Product is for the set (Driver & Passenger Side.)

    Made from 18 Gauge Steel.

    Comes with hardware needed for install.

    Select options
  • L&W Sak- It Scrap Sak

    $38.00

    These are the Sak-It Brand Scrap Sak’s with our L&W Logo.

    You can only get these here at landwfab.com

    Don’t leave your trash junking up your ride, when you can Sak-It!

    Add to cart
  • Turbo S/Pro XP- Spindle End Replacement

    $20.00$40.00

    This is a replacement spindle end for Turbo S AND Pro XP tie rods.

    If you have just purchased our tie rods, the spindle end will come with them. 

    This is just a replacement piece. 

    Select options
  • PRO XP FORWARD A Arms

    $700.00$750.00

    1.5 x .120 and 1.25 x .120 DOM

    1.75″ Forward offset

    Can clear 33-34″ tires

    The stock steering stop may need to be cut back 1/2″ unless you are running portals.

    L and W offers a life time warranty on bending and breaking the arm.

    Please select raw in the color options if you do not want powder coating.

    These A Arms do not require new bushings. You may use your factory bushings.

    PLEASE ALLOW 7-10 DAYS on BACK-ORDER PRODUCTS or POWDER COATING

    Select options
  • Windshields for L&W Cages

    $220.00$385.00

    These windshields are made to fit L&W Production cages ONLY!

    Windshields are made from 3/16 polycarbonate with MARGARD coating.

    The maragard coating makes it scratch resistant. (Resistant not proof)

    Comes complete with all hardware for easy installation

    Made in the USA

    Select options
  • PRO XP- 2 Seater Tree Kickers

    $580.00$640.00

    This listing is for a set (driver and passenger) of 2 seater tree kickers.

    2020-CURRENT POLARIS RZR PRO XP 2 SEAT (ALL MODELS) TREE KICKERS
    DESIGNED FOR 64″ MACHINES

    MADE OF DOMESTIC DOM (1.75X.120 WALL AND 1.5X.120 WALL)
    PROVIDES PROTECTION OF LOWER PLASTICS AND FRAME
    COMES RAW OR ANY POLARIS OEM COLOR
    HEAVY DUTY THROUGH-FRAME HARDWARE MADE BY L&W FAB
    NO DRILLING REQUIRED. 

    COMES STANDARD WITH BLACK PLASTIC END CAPS

    American Made. 

    Installation Instructions: https://landwfab.com/wp-content/uploads/2021/11/pro-2-seat-instructions.pdf

    Select options
  • PRO XP- Sport Bumper

    $300.00$350.00

    This listing is for PRO XP models only.

    (NON R MODEL)

    FITMENT: 19-Current PRO XP

    This front bumper comes with all hardware needed to install.

    Made of 1.75” x .120” DOM , 11GA and 3/16” plate
    Bumper works in CONJUNTION with aftermarket winch mounts.

    This bumper is not a winch mount- Only a Fairlead mount
    Works with most popular aftermarket winch mounts including KFI, SUPERATV, and L&W.
    Integrated holes in corners for 3⁄4” blinkers

    These bumpers use a 6 inch fairlead. 

    (fairlead is not included UNLESS purchased as an add on below)

    we do not offer custom colors. 

    Select options
  • PRO XP- Direct Bolt Radius Rods

    $240.00$465.00

    THIS LISTING IS FOR PRO XP MODELS ONLY.

    The lowers are High clearance and always come Direct Bolt.

    The Direct Bolt Uppers come with no adjustment as they are direct fit. 

     

    *Adjustable uppers are usually necessary to correct any camber issues that you may have or experience on your machine.  Most times if you plan to change tender springs, or if you are running a bigger set up (portals, lifts, changing ride height most times will cause +/- camber that you will need to correct with adjustable uppers.) 

    Includes all misalignment spacers needed for install. 

    They are 6061 Aluminum, and made in the USA. 

    These Radius Rods hold a Lifetime Warranty.

    Select options
  • PRO XP Sway Bar Links

    $150.00

    Made of 6061

    This listing is for a set of 2

    Add to cart
  • PRO XP- 4 Seater Tree Kickers

    $700.00$775.00

    This listing is for a set (driver and passenger) of 4 seater tree kickers.

    2020-CURRENT POLARIS RZR PRO XP 4 SEAT (ALL MODELS) TREE KICKERS
    MADE OF DOMESTIC DOM (1.75X.120 WALL AND 1.5X.120 WALL)
    PROVIDES PROTECTION OF LOWER PLASTICS AND FRAME
    COMES RAW OR ANY POLARIS OEM COLOR
    HEAVY DUTY THROUGH-FRAME HARDWARE MADE BY L&W FAB

    DESIGNED FOR 64″ MACHINES

    NO DRILLING REQUIRED. 

    American Made. 

    Install Instructions: PowerPoint Presentation (landwfab.com)

    Select options
  • PRO XP- Standard A-Arms

    $350.00$750.00

    These High Clearance A Arms are raw material. 1 1/4 tubing.120 wall dom.
    L and W offers a life time warranty on bending and breaking the arm.

    Please select raw in the color options if you do not want powder coating.

    These A Arms do not require new bushings. You may use your factory bushings.

    PLEASE ALLOW 7-10 DAYS on BACK-ORDER PRODUCTS or POWDER COATING

    Select options
  • 2 Seater Pro XP Cage

    $1,300.00$1,700.00
    IMPORTANT CAGE INFORMATION
    ALL CAGES ORDERED THAT STATE “ON BACKORDER” ARE ANTICEAPATING A LEAD TIME OF 4-8 WEEKS ONCE PURCHASED TO BE COMPLETED, PLEASE ALSO NOTE THAT IF CHOOSING POWDER COAT IT COULD BE AN ADDITIONAL 2 WEEKS. THERE IS NO RUSH OPTION AVAILABLE ON BACKORDERED CAGES.
     
    -IF YOU ARE NEEDING A CAGE SHIPPED, PLEASE SEND AN EMAIL TO Taylor@landwfab.com (mailto:Taylor@landwfab.com) for a shipping quote.
    Please provide your full ship to address along with the cage SKU # you wish to purchase or the order number for your cage so that she can get you an accurate shipping cost.
    Please allow 24 – 48hrs for an email response with your quote.
    -ALSO PLEASE NOTE ALL SALES ARE FINAL.
     
    -PICKUP INFORMATION
    When placing an order that you plan to pick up, please put in the notes at checkout that it is local pick up. Once your cage is ready, we would reach out to you via email/ call to schedule a pickup date that works best for you.

    Cage Includes aluminum roof  and WILL ALWAYS COME STANDARD WITH GRAB HANDLES.

     

    Please indicate color of cage and roof, if you chose the powder coat option.

     

    Select options
  • PRO XP / TURBO R Rear Bumper

    $400.00$455.00

    Pro Xp/ Pro R Rear Bumper

    Fits 2020-current Polaris PRO XP and TURBO R
    Easy bolt on installation. No drilling required
    Made from 1.75” x .120 DOM

    Select options
  • PRO Grill WITH Lightbar

    $185.00

    PRO XP/R GRILL

    FITMENT: All Pro XP models and Pro R/ Turbo R models

    If you choose to get the Grill it does Come with the Light Bar (does not include wiring harness)

    Easily snaps in and out.

    Not screwed to the machine.

    Must drill 4 holes to install snap tab for main grill.

    Side Vent color will be the same color you choose for the grill overlay color.

    Select options
  • Seat lowering Base Hardware Kit

    $15.00$30.00

    This Listing is for a SET for TWO seat lowering base hardware kits or for a SINGLE seat base.

    This is not required with the purchase of a new set of bases. 

    This is only a replacement kit. 

    This hardware kit is a replacement for RZR as well as General seat lowering bases. 

    Select options
  • PRO XP Long Travel Kit

    $2,750.00$3,750.00

    Fits 2020-current Polaris PRO XP

    Bolt on installation.

    No drilling required

    This kit adds 4” to each side of a PRO XP giving it a 72” width with stock offset wheels.

    Adds 3.5” to the wheelbase.

    Front a arms are 1.75” forward offset, and rear trailing arms are 1.75” rear offset, which improves stability.

    A arms are made from 1.5” DOM. and are high clearance.

    Front and Rear keep factory shock location.

    Can use factory PRO XP bushings and factory ball joints.

    Only Steel Parts ( A Arms and Trailing Arms will come powder coated ). Additional add on charge for powder coating radius rods is available.

    Kit includes:

    • Front upper and lower A arms. (Non- Adjustable)( Stock size ball joints only. These are not offered for Mega Ball Joints)
    • Set of Tie Rods with L&W HD rebuild-able inner joints.
    • High Clearance Steel HD Trailing Arms
    • High Clearance Billet Aluminum Radius Rods with adjustable uppers.
    • (1) Extended brake line for front passenger side

     

    REQUIRES THE USE OF TURBO S AXLES and RZR XP/TURBO S HUBS that are not included

     

    HUB OEM PART # 5141353-067

     

    WE RECOMMEND A SPRING UPGRADE, AS THIS KIT WILL GREATLY INCREASE THE SOFTNESS OF

    THE SPRINGS. (SPRINGS WILL COME POWDER COATED BLACK- ZBROZ)

    ****If Purchasing Ball Joints or A Arm Bushings, they WILL NOT come installed****

    Select options
  • PRO XP FRAME CROSS MEMBER

    $135.00$260.00

    Made from 3/16 STEEL
    The factory prop shaft crossmember is known to bend. When the crossmember bends, it
    changes the prop shaft angle, and can lead to premature bearing failure and vibrations.

    Our crossmembers are 2.5x thicker and add strength where it is needed.
    Works with factory or aftermarket bearing carriers.
    Bolts in using factory hardware

    FITMENT:

    2020-CURRENT PRO XP 4 SEAT

    2020-CURRENT PRO XP 2 SEAT

    2020-CURRENT PRO XP 4 SEAT REAR

    Select options
  • PRO XP /PRO R/ TURBO R- Packout Mount

    $145.00

    -Made from 10GA Steel
    -Comes powder coated black
    -(2) holes must be drilled to install
    -An angled design allows more room for cooler
    -When used in the PRO R models, many popular coolers will fit and still open. (Ozark Trail 26qt
    works best

     

    Add to cart
  • End Caps for Bumpers/Tree Kickers

    $12.00$20.00

    These are plastic replacement end caps for L&W bumpers and tree kickers. 

    Select options
  • Turbo R – 2 Seater Tree Kickers

    $585.00$645.00

    2022CURRENT POLARIS RZR TURBO R 2 SEAT (ALL MODELS) TREE

    KICKERS


    FITMENT:


    Fits All trims of The Turbo R, and also works well with Pro XP long travel

    • MADE OF DOMESTIC DOM (1.75X.120 WALL AND 1.5X.120 WALL)
    • PROVIDES PROTECTION OF LOWER PLASTICS AND FRAME

    • COMES RAW OR ANY POLARIS OEM COLOR

    • HEAVY DUTY THROUGHFRAME HARDWARE MADE BY L&W FAB

    • NO DRILLING REQUIRED

    • DESIGNED FOR 7274” MACHINES


    • Hardware for complete set (1 driver and 1 passenger):


      (6) plastic end caps for 1.75 x .120 tube


      (12) SAE ½” flat washers


      (6) ½” lock washers


      (6) ½13 THIN nylon insert locknut


      (6) ½”13 x 1” GR8 hex bolts


      (4) pro xp front frame PIN (L&W made)


      (2) pro xp rear frame PIN (L&W made)

    American Made. 

     

     

    Select options
  • 4 Seater Pro XP Cage

    $2,000.00$2,500.00
    IMPORTANT CAGE INFORMATION
    ALL CAGES ORDERED THAT STATE “ON BACKORDER” ARE ANTICEAPATING A LEAD TIME OF 4-8 WEEKS ONCE PURCHASED TO BE COMPLETED, PLEASE ALSO NOTE THAT IF CHOOSING POWDER COAT IT COULD BE AN ADDITIONAL 2 WEEKS. THERE IS NO RUSH OPTION AVAILABLE ON BACKORDERED CAGES.
     
    -IF YOU ARE NEEDING A CAGE SHIPPED, PLEASE SEND AN EMAIL TO Taylor@landwfab.com (mailto:Taylor@landwfab.com) for a shipping quote.
    Please provide your full ship to address along with the cage SKU # you wish to purchase or the order number for your cage so that she can get you an accurate shipping cost.
    Please allow 24 – 48hrs for an email response with your quote.
    -ALSO PLEASE NOTE ALL SALES ARE FINAL.
     
    -PICKUP INFORMATION
    When placing an order that you plan to pick up, please put in the notes at checkout that it is local pick up. Once your cage is ready, we would reach out to you via email/ call to schedule a pickup date that works best for you.

    Cage Includes aluminum roof and WILL ALWAYS COME STANDARD WITH FRONT GRAB HANDLES.

     

    Please indicate color of cage and roof, if you chose the powder coat option.

    Select options
  • PRO XP – RADIUS ROD PLATE

    $165.00$185.00

    Fitment: 2020current Polaris Pro XP


    Made from 6061T6 Billet aluminum



    Adds strength as well as looks



    Comes with pull point

    PLEASE NOTE: If powder coat option is chosen only the plate itself will be powdered, the pull point will always be billet aluminum.

    Select options
  • PRO Grill WITHOUT Lightbar

    $165.00

    PRO XP/R GRILL

    FITMENT: All Pro XP models and Pro R/ Turbo R models

    Easily snaps in and out.

    Not screwed to the machine.

    Must drill 4 holes to install snap tab.

    Side Vent color will be the same color you choose for the grill overlay color.

    Side Vents DO NOT WORK WITH PRO XP MODELS

    TO PURCHASE JUST THE SIDE VENTS PLEASE CLICK THE LINK BELOW:

    https://landwfab.com/product/pro-r-turbo-r-side-vents/

    Select options
  • L&W Rear Inner Fender Mud Guard- PRO R

    $55.00

    FOR PRO R MODELS ONLY! (All Trims)

    This Product is for the set (Driver & Passenger Side.)

    Made from 18 Gauge Steel.

    Comes with hardware needed for install.

    Select options
  • PRO XP- Steel HD Trailing Arms

    $825.00$875.00

    FITMENT: 2020-CURRENT PRO XP

    These Steel HD Trailing Arms are built from 1″ 1/2 x 3 3/16 Rectangle Tubing.

    You may choose the color of the Trailing arm itself, however the brake line logo bracket comes powder coated black. 

    These trailing arms hold a lifetime warranty. 

    They are not under warranty for racing applications, and there is no warranty on wear parts. (Uniball/Misalignments). 

    Select options
  • Offroad Rugged X-Grip Phone / Tablet Mount for Roll Cage

    $65.33$125.85
    • American made
    • Comes with Ram Mounts X-Grip
    • Each clamp is 1/2″ thick
    • These will fit 1.75″ tubing
    • Great way to mount your phone to any tubing
    • Made from 6061-T6 Billet Aluminum

     Large Ram mount phone holder will except a phone width from 1.75″ to 4.50″

     Small Ram mount tablet holder will except a tablet width from 2.50″ to 5.75″

     Large Ram mount tablet holder will except a tablet width from 6.25″ to 8.10″ and 10.25″ long

    Select options
  • 1.5” BRAKE LINE CLAMPS

    $45.00$80.00

    1.5” BRAKE LINE CLAMPS

    Made from 6061 billet aluminum


    Clamps work with the following L&W Arms.


    All Pro XP A arms


    All Turbo S A arms


    All long travel A arms


    Also can be used on other arms where 1.5” OD tubing is used


    Comes with stainless hardware

    Select options
  • Turbo S/Pro XP Front A-Arm Bushings

    $220.00

    PLEASE NOTE THAT THESE MAY BE PURCHASED AS “AVAILABLE ON BACKORDER”, MEANING SHIP TIMES WILL BE DELAYED. (CURRENT ETA IS 4 WEEKS OUT.)

    Select options
  • Pro XP Winch Mount

    $165.00

    This Winch Mount is specifically made for the Pro XP, and will only work with the PRO XP.

    Fits 6000 lb. Winch.

    This item comes in black only.

    Select options
  • PRO XP FORWARD A Arms (MEGA BALL JOINT)

    $700.00$750.00

    PRO XP FORWARD A Arms (MEGA BALL JOINT)

    1.5 x .120 and 1.25 x .120 DOM

    1.75″ Forward offset

    Can clear 33-34″ tires

    L and W offers a life time warranty on bending and breaking the arm.

    Please select raw in the color options if you do not want powder coating.

    These A Arms do not require new bushings. You may use your factory bushings.

    PLEASE ALLOW 7-10 DAYS on BACK-ORDER PRODUCTS or POWDER COATING

     

    For Standard Ball Joint A Arms: https://landwfab.com/product/pro-xp-forward-a-arms/

    Select options
  • PRO XP- Full Suspension Kit

    $2,300.00$2,450.00

    This kit is for PRO XP Models ONLY.

     

    Please see “additional info” below for what all products this full suspension kit includes

     

    (PLEASE NOTE WHEN CHOOSING A POWDER COAT COLOR OPTION THAT ONLY THE STEEL PARTS (A-ARMS and TRAILING ARMS) WILL BE POWDER COATED THAT COLOR, THE OTHER ALUMINUM ITEMS (TIE RODS, RADIUS RODS and SWAY BAR LINKS) WOULD COME RAW BILLET ALUMINUM- unless upgraded to powder coated radius rods below.)

    Select options
  • POLARIS RZR PRO XP HEAVY-DUTY AXLES – RHINO 2.0

    $239.95

    Fitment

    • Polaris RZR PRO XP : 2020+
    • Polaris RZR PRO XP 4 : 2020+

    Features

    • 25% stronger than stock
    • Made with 4340 chromoly steel
    • Proprietary heat treatment for superior strength and longevity
    • Operates at high CV angles
    • Field and lab tested for extreme strength and endurance
    • Industry-leading 18-month warranty
    Select options
  • Worlds Best Belt – RZR Pro XP

    $179.95

    The 1202 World’s Best Belt has a taller side profile, allowing for more hookup on the clutches when compared to the stock belt. This is an upgraded belt for  the RZR Pro XP. 

    • Manufacturing, quality control certifications — ISO-14001, ISO-9001, and IATF-16949.
    • 3rd Generation heavy-duty, high-twist Aramid Fiber cord for HIGH HORSEPOWER TENSILE LOAD requirements. Making it the strongest belt on the market, surpassing even our EX and Sand Storm lines.
    • Highest shock load rating to date being able to withstand the power of the 400hp machines.
    • Increased top cog pressure load design that increases sidewall rigidity, prevents top cog bowing, but still allows for increased rotational flexibility.
    • Bottom cog uses HIGH MODULOUS RUBBER COMPOUND (BZX1) for better heat resistance and heat dissipation.
    • Bottom cog is impregnated with short Aramid Fibers for better belt-to-sheave adhesion and reduced overall belt temperature.
    • Latest bottom cog design for greater rotational efficiency at full shift.
    • Precision ground sidewall angle (SCUFFING) for smooth engagement, increased power transfer and lower operating belt temperature.
    • Aramid Fiber cord, versus polyester, wraps over bottom cogs for increased bottom cog strength.
    • Increased cord pop-out resistance.

    FITMENT:

    2020-21 Polaris RZR PRO XP

     

    This belt is for the rider / racer that is looking for the latest in technology and proven performance.

    Add to cart
  • Exhaust Cover- Pro XP/ TURBO R

    $100.00

    Specifications on Exhaust Cover:

    It is made from 18 gauge steel.

    No modifications are required to the machine

    Works with factory and slip on exhausts

    Does Not Work with Aftermarket Head Pipe

    Fitment:

    2020- Current PRO XP

    2022- Current TURBO R

    Does not fit a PRO R

    Select options
  • Windshields for Stock Cage

    $210.00$260.00

    These windshields are made to fit L&W Production cages ONLY!

    Windshields are made from 3/16 polycarbonate with MARGARD coating.

    The maragard coating makes it scratch resistant. (Resistant not proof)

    Comes complete with all hardware for easy installation

    Made in the USA

    Select options

Click here to assign a widget for this area.