Category: RZR Turbo

RZR Turbo

Showing 1–40 of 48 results

  • Seat Lowering Bases

    $80.00$125.00
    INTRODUCING THE  L&W SEAT LOWERING BASE! 
     
    -Easier to Install
    -Uses Stock Slider
    -Slider Plate integrated
    -Harness 5th Point Mount
    -Lowers 2”
    -Reclines 5.2 degrees
    • Powder Coated Black 
    • HARDWARE KIT IS INCLUDED, you do not need to purchase it separately.
    • There are pieces you need from the original seat base. 
    • Works with MOST aftermarket seats. (L&W is not responsible for fitment issues when using aftermarket seats)
    • ALSO please note that since these recline the seat 5.2 degrees you will not be able to slide the seat all the way back, causing you to lose some leg room. 

    THESE DO NOT FIT PRO XP, TURBO R, or PRO R MODELS

     
    Select options
  • 1K/TURBO/RS1- Direct Bolt Radius Rods

    $240.00$675.00

    THIS LISTING IS FOR 1K/TURBO/RS1 MODELS ONLY.

    2014-2023 models

    This listing is for the Direct Bolt Radius Rods.

    The lowers are High clearance. 

    Includes all spacers needed for install. 

    They are 6061 Aluminum, and made in the USA. 

    These Radius Rods hold a Lifetime Warranty. 

    Select options
  • 1K/Turbo Tie Rods – Factory Style

    $189.00$325.00

    These Tie Rods Fit Polaris RZR 1000 and Turbo

    2014-2024 models

    Specs on the Rods:

    These are factory style ball and socket tie rods. 

    This listing is for a SET

    6061 Aluminum. 

    Made in America

    Lifetime Warranty on rod itself.

    Comes with Spindle Ends (You do not need to purchase the spindle ends separate from this kit, unless you need a replacement spindle end) 

    To determine whether you have M14 or M16, please measure the ends of you factory tie rods (the side that screws into the rack). If the end is less the 1/2″ you will need M14, if it is over 1/2″ you will need M16. The turbo model usually takes M16 ( measuring is recommended ), the 1000 model is not consistent and will need to be measured. **2016 Turbo will always be M14**

     

    Factory ends are not warrantied, only the tie rod itself. 

     

    Specs for HD Rebuild-able Tie Rod Ends:

    Fully rebuildable

    Comes assembled with grease ready for installation Compatible with all L&W tie rods plus many others Starts with heat treated 4140 Black oxide finished

    100 percent made in USA

    This product holds an 18 month warranty

    Options:

    1) M14x1.5 rack side by m14x1.5 tie rod side. 5-5/8″ total length. (4″ length from rack to end of Jam nut)

    2) M16x1.5 rack side by m14x1.5 tie rod side. 5-5/8″ total length. (4″ length from rack to end of jam nut)

    https://landwfab.com/product-category/rzr-parts/tie-rods/

    https://www.facebook.com/landwfab/

     

    Select options
  • Aftermarket Mount Plate for Milwaukee Packout

    $120.00

    Milwaukee Packout mount plate:

    2014-2023 models

    Works with all Polaris RZR XP1000/Turbo, Turbo S. Also works with High lifter editions.

    Made with 10ga HRPO steel.
    Easily installed/removed with no tools using the supplied hardware.
    Mount is slotted for different configurations of boxes to maximize trunk room for coolers.
    Most coolers under 26qt will still fit.

    Add to cart
  • High Clearance A Arms 1K/Turbo (2017- 2023 Models)

    $300.00$725.00

    These High Clearance A Arms are raw material.

    1 1/4 tubing .120 wall DOM. 

    L and W offers a life time warranty on bending and breaking the A arms. 

    DOES NOT COME TAPPED FOR GREASE FITTINGS. 

    Please select raw in the color options if you do not want powder coating. 

    These now take 17 and up model bushings.

    If you have a 14-16 model, you will need to purchase 17 & up model bushings.

    Bushing Sold Separately. Please see link in description for bushings.

     

    Select options
  • Radius Plate- 1K/TURBO/RS1

    $115.00$140.00

    2014-2023 models

    This radius plate has a lifetime warranty.

    Made from 6061 Aluminum.

    We make this product in Temple, Ga. 

    1K/ Turbo/ RS1

    DOES NOT WORK WITH FACTORY BUMPER.

    https://landwfab.com/product-category/rzr-parts/radius-rods/

    https://www.facebook.com/landwfab/

    Select options
  • 1K/Turbo -Spindle End for Tie Rods

    $20.00$40.00

    This is a REPLACEMENT spindle end for tie rods. 

    If you have just purchased our tie rods, the spindle end will come with them. 

    This is just a replacement piece. 

    Select options
  • Clevis Style Tie Rods (1K/Turbo)

    $215.00

    These are clevis style tie rods (heavy duty).

    This listing is for a SET

    Tie Rod ends are not consistent across all models or years. Please make sure to measure the rack end of stock tie rods to be sure of which size you need.

    To determine what size you need, please measure the end of your tie rod that screws into the rack, if the measurement is less the 1/2″ you will need M14, if it is more then 1/2″ you will need M16.

    These tie rods are made to work well for a racing style application. 

    6061 Aluminum. 

    Made in America

    Life Warranty. 

    Ends are not warrantied, only the tie rod itself. 

     

    Select options
  • 1.75″ Forward 1K/Turbo High Clearance A Arms (Full Kit)

    $635.00$725.00

    L and W offers a life time warranty on bending and breaking the A arms.

    Will NOT work with 6+1 or 5+2 Offset Wheels, UNLESS you are running either a steering stop or 1inch wheel spacers. 

    DOES NOT COME TAPPED FOR GREASE FITTINGS

    Please select raw in the color options if you do not want powder coating.

    These now take 17 and up model bushings.

    If you have a 14-16 model, you will need to purchase 17 & up model bushings.

    Bushing Sold Separately. Please see link in description for bushings.

    PLEASE ALLOW 7-10 DAYS on BACK-ORDER PRODUCTS or POWDER COATING

    Select options
  • 1K/TURBO- Race Style Winch Bumper (2019-2023)

    $300.00$350.00

    This listing is for 1K/TURBO models only.

    (2019-2023)

    This bumper comes with all mounting winch plates and hardware needed to install.

    (DOES NOT INCLUDE FAIRLEAD)

    Setup to Mount Standard 3,500 lb to 6,000 lb winch’s. (Black Ops preferred, but will take other winches brands as well)

    Wide Spool Winches DO Fit In This Bumper

    These bumpers use a 6 inch fairlead.

     

    Select options
  • Tree Kicker Bolt Kit

    $40.00$150.00

    This tree kicker bolt kit is for 2 or 4 seater L&W tree kickers. 

    (1K/TURBO/TURBO-S) 2 seater set comes with 4 L bolts.

    (1K/TURBO/TURBO-S) 4 seater set comes with 6 L bolts.

    (PRO XP) 2 seater set comes with 6 frame pins. 

    (PRO XP) 4 seater set comes with 8 frame pins.

    This is just a replacement kit. 

    For new tree kickers, click the link below. 

     

    If you are looking for new tree kickers please click here- https://landwfab.com/?s=TREE+KICKERS&product_cat=0&post_type=product

    http://facebook.com/landwfab

    Select options
  • 1K/TURBO/RS1- Sway Bar Links

    $100.00

    PLEASE ALLOW 7-10 DAYS on BACK-ORDER PRODUCTS or POWDER COATING

     

    Made of 6061

    Add to cart
  • Cooler Mount for 1k/ Turbo

    $100.00

    Cooler Mounts:

    Fits a 1K/Turbo (For Turbo S, please see Turbo S Listing)

    1. Works with All RZR XP including highlifter edition
    2. Uses eye bolt Grip mount
    3. All hardware included
    4. Made from 3/16 HRPO
    5. Fully adjustable to fit over 30 different cooler models including these top models:
       i) YETI Tundra 35
      ii) RTIC 20
      iii) YETI 20
      iv) Ozark 26
      v) NICE 26

    IS NOT COMPATIBLE WITH POLARIS OR PELICAN COOLERS.
    6. Comes powder coated black

     

    [video width="1920" height="828" mp4="https://landwfab.com/wp-content/uploads/2020/10/RZR-XP-TURBO-COOLER-MOUNT.mp4"][/video]
    Add to cart
  • Keller Ball Joint

    $130.00$510.00

    If you are needing ball joints for a full set (4) of A Arms, please choose a set of 4. 

    If you are needing them for Uppers, choose a set of 2. 

    If you are needing them for Lowers, choose a set of 2.

     

    The Mega Ball Joints are used for our mega ball joint a arms. The will not fit a regular a arm.

    These ball joints are for rzr only (XP, TURBO, RS1, PRO XP, TURBO S). They do not fit a general or Ranger. 

     These ball joints have a hardened body and stem. Stem is built from AMERICAN made 4340 and hardened for maximum strength and wear resistance. Adjustable and greaseable with a replaceable boot.

    Select options
  • 2 Heim-1K/TURBO/RS1- Radius Rods

    $240.00$465.00

    THIS LISTING IS FOR 1K/TURBO/RS1 MODELS ONLY.

    2014-2023 models

    This listing is for the 2 Heim Radius Rods.

    The lowers are High clearance. 

    Includes all spacers needed for install. 

    PLEASE NOTE THAT IF YOU HAVE GEN3 SUPERATV PORTALS YOU WILL NEED TO PURCHASE THE UPPER ADJUSTABLE RADIUS RODS (1 HEIM or 2 HEIM) in order for your suspension to have enough room to travel without busting the portal bracket ear. 

    They are 6061 Aluminum, and made in the USA. 

    These Radius Rods hold a Lifetime Warranty. 

    Does not include radius plate, to purchase radius plate click here

    FITMENT:

    10mm is for year models 2014 to early 2017

    12mm is for year models Late 2017-2023

    If your year model falls in the mid 2017 range, you can determine your bolt size by the socket size. If the socket is 15mm, then you will need a 10mm bolt. If it is a 18mm, then you will need the 12mm bolt.

    Select options
  • L&W Sak- It Scrap Sak

    $38.00

    These are the Sak-It Brand Scrap Sak’s with our L&W Logo.

    You can only get these here at landwfab.com

    Don’t leave your trash junking up your ride, when you can Sak-It!

    Add to cart
  • 1K/Turbo Rear Bumper (2019-2023)

    $400.00$445.00

    This listing is for 1K/TURBO models only.

    This bumper comes with a rear radius plate (steel-powdered black) and all hardware needed to install. 

    Made from 1.75 x .120 Wall Steel

    CHECK OUT our Additional Bumper Add Ons and Upgrades Below!

    Select options
  • 1K/Turbo- 2 Seater Tree Kickers

    $475.00$525.00

    This listing is for a set (driver and passenger) of 2 seater tree kickers.

    Model fitment: 1K/Turbo

    American Made. 

    Select options
  • Front Winch Bumper-1K/TURBO- (2019 to 2023)

    $450.00$500.00

    This listing is for 2019-2023 1K/TURBO MODELS ONLY.

    This bumper comes with all mounting winch plates and hardware needed to install.

    (DOES NOT INCLUDE FAIRLEAD)

    Setup to Mount Standard 3,500 lb to 6,000 lb winch’s. (Black Ops preferred, but will take other winches brands as well)

    Wide Spool Winches DO Fit In This Bumper

    These bumpers use a 6 inch fairlead. 

     

    WITH BROW: LOOPS AROUND HEADLIGHTS

    NO BROW: UNDER HEADLIGHTS

     

    Select options
  • Reverse Light

    $105.00$130.00

    This Reverse Light will work with: Turbo S models 2018-2020 and 1k/Turbo Models 2019-2020.

    It comes with 12ft. of wire 

    5/10 rocker switch with fuse and relay 

    Select options
  • Aftermarket Snap In Grill

    $160.00

    Options for outline color and L&W logo

    The grill mesh will always be black

     

    Fitment:

    Turbo S

    19-current models 1K/Turbo

    *NOTE: THIS GRILL WILL NOT WORK WITH THE FACTORY POLARIS BUMPER WITHOUT MAKING SLIGHT MODIFICATIONS TO FIT.*

    Select options
  • 1.25″ Brake Line Clamps

    $45.00$60.00

    Fit’s 1K/TURBO

    Does Not fit Turbo S or Pro XP

     

    Select options
  • Windshields for L&W Cages

    $220.00$385.00

    These windshields are made to fit L&W Production cages ONLY!

    Windshields are made from 3/16 polycarbonate with MARGARD coating.

    The maragard coating makes it scratch resistant. (Resistant not proof)

    Comes complete with all hardware for easy installation

    Made in the USA

    Select options
  • 1K/Turbo Front Bumper (2019-2023)

    $430.00

    1K/Turbo Front Bumper (2019-2023)

    This Bumper is a non-winch bumper that is designed to fit a 1K or Turbo Polaris RZR.
    It is specific to 2019-2023.

    It comes with all hardware needed.

    Select options
  • 1 Heim-1K/TURBO/RS1- Radius Rods

    $240.00$465.00

    THIS LISTING IS FOR 1K/TURBO/RS1 MODELS ONLY.

    2014-2023 models

    This listing is for the 1 Heim Radius Rods.

    The lowers are High clearance. 

    Includes all spacers needed for install. 

    PLEASE NOTE THAT IF YOU HAVE GEN3 SUPERATV PORTALS YOU WILL NEED TO PURCHASE THE UPPER ADJUSTABLE RADIUS RODS (1 HEIM or 2 HEIM) in order for your suspension to have enough room to travel without busting the portal bracket ear. 

    They are 6061 Aluminum, and made in the USA. 

    These Radius Rods hold a Lifetime Warranty. 

    Does not include radius plate, to purchase radius plate click here

    FITMENT:

    10mm is for year models 2014 to early 2017

    12mm is for year models Late 2017-2023

    If your year model falls in the mid 2017 range, you can determine your bolt size by the socket size. If the socket is 15mm, then you will need a 10mm bolt. If it is a 18mm, then you will need the 12mm bolt.

    Select options
  • Exhaust Cover for RZR Turbo/Turbo S

    $100.00

    Specifications on Exhaust Cover for RZR:

    It is made from 18 gauge steel.

    No modifications are required to the machine

    Works with factory and slip on exhausts

    Does Not Work with Aftermarket Head Pipe

    Fitment:

    2018-Current XP Turbo

    2018- Current Turbo S

    Does not fit a 1000 model

    For exhausts please click the link below:

    https://landwfab.com/product-category/trinity-racing-products/mufflers/

    Select options
  • 4 Seater Tree Kickers-1K/TURBO

    $700.00$775.00

    This listing is for a set (driver and passenger) of 4 seater tree kickers.

    Model fitment: 1K/Turbo

    American Made. 

    Select options
  • Gordon Low Cage- 1K/Turbo/Turbo S- 4 Seater

    $2,200.00$2,700.00

    Gordon Low is a 8″ Chop

    If you would like to purchase a windshield to fit this cage please click here!

     

    • Price includes Aluminum Roof.
    • Cage DOES NOT come standard with grab bars or intrusion bars. Those must be added for an additional charge.
    • Please indicate color of cage and roof, if you chose the powder coat option.

    (See shipping details in Additional Info below!)

     

    IMPORTANT CAGE INFORMATION
    ALL CAGES ORDERED THAT STATE “ON BACKORDER” ARE ANTICEAPATING A LEAD TIME OF 4-8 WEEKS ONCE PURCHASED TO BE COMPLETED, PLEASE ALSO NOTE THAT IF CHOOSING POWDER COAT IT COULD BE AN ADDITIONAL 2 WEEKS. THERE IS NO RUSH OPTION AVAILABLE ON BACKORDERED CAGES.
     
    -IF YOU ARE NEEDING A CAGE SHIPPED, PLEASE SEND AN EMAIL TO Taylor@landwfab.com (mailto:Taylor@landwfab.com) for a shipping quote.
    Please provide your full ship to address along with the cage SKU # you wish to purchase or the order number for your cage so that she can get you an accurate shipping cost.
    Please allow 24 – 48hrs for an email response with your quote.
    -ALSO PLEASE NOTE ALL SALES ARE FINAL.
     
    -PICKUP INFORMATION
    When placing an order that you plan to pick up, please put in the notes at checkout that it is local pick up. Once your cage is ready, we would reach out to you via email/ call to schedule a pickup date that works best for you.
    Select options
  • Aftermarket Snap In Grill with Light Bar

    $185.00

    Comes with Light Bar (does not include wiring harness)

    Options for outline color and L&W logo

    The grill mesh will always be black

     

    Fitment:

    Turbo S

    19-current models 1K/Turbo

    *NOTE: THIS GRILL WILL NOT WORK WITH THE FACTORY POLARIS BUMPER WITHOUT MAKING SLIGHT MODIFICATIONS TO FIT.*

    Select options
  • (MEGA) 1.75″ Forward High Clearance A Arms- 1K/TURBO

    $635.00$725.00

    THIS LISTING IS FOR A FULL KIT.

    L and W offers a life time warranty on bending and breaking the A arms.

    These A Arms are constructed for Mega Ball Joints ONLY. 

    Will NOT work with 6+1 or 5+2 Offset Wheels.

    Please select raw in the color options if you do not want powder coating.

    Our A Arms now require 17+ model bushings.

    If you have a 14-16 you will need to purchase the bushing kit for the 17+ model. 

    Bushing Sold Separately. Please see link in description for bushings.

    PLEASE ALLOW 7-10 DAYS on BACK-ORDER PRODUCTS or POWDER COATING

    Select options
  • Seat lowering Base Hardware Kit

    $15.00$30.00

    This Listing is for a SET for TWO seat lowering base hardware kits or for a SINGLE seat base.

    This is not required with the purchase of a new set of bases. 

    This is only a replacement kit. 

    This hardware kit is a replacement for RZR as well as General seat lowering bases. 

    Select options
  • End Caps for Bumpers/Tree Kickers

    $12.00$20.00

    These are plastic replacement end caps for L&W bumpers and tree kickers. 

    Select options
  • 1K/Turbo/Turbo S- 2 Seater Cage

    $1,300.00$1,850.00

    Cages are made out of .120 DOM – 1.75″ in diameter.

    IMPORTANT CAGE INFORMATION
    ALL CAGES ORDERED THAT STATE “ON BACKORDER” ARE ANTICEAPATING A LEAD TIME OF 4-8 WEEKS ONCE PURCHASED TO BE COMPLETED, PLEASE ALSO NOTE THAT IF CHOOSING POWDER COAT IT COULD BE AN ADDITIONAL 2 WEEKS. THERE IS NO RUSH OPTION AVAILABLE ON BACKORDERED CAGES.
     
    -IF YOU ARE NEEDING A CAGE SHIPPED, PLEASE SEND AN EMAIL TO Taylor@landwfab.com (mailto:Taylor@landwfab.com) for a shipping quote.
    Please provide your full ship to address along with the cage SKU # you wish to purchase or the order number for your cage so that she can get you an accurate shipping cost.
    Please allow 24 – 48hrs for an email response with your quote.
    -ALSO PLEASE NOTE ALL SALES ARE FINAL.
     
    -PICKUP INFORMATION
    When placing an order that you plan to pick up, please put in the notes at checkout that it is local pick up. Once your cage is ready, we would reach out to you via email/ call to schedule a pickup date that works best for you.

    Cage Includes aluminum roof

    Cage DOES NOT come standard with grab bars. Those must be added for an additional charge.

    Please indicate color of cage and roof, if you chose the powder coat option.

    Select options
  • 1K/Turbo/RS1- Steel HD Trailing Arms

    $825.00$875.00

    FITMENT: 1K/TURBO/RS1

    These Steel HD Trailing Arms are built from 1″ 1/2 x 3 3/16 Rectangle Tubing.

    You may choose the color of the Trailing arm itself, however the brake line logo bracket comes powder coated black. 

    These trailing arms hold a lifetime warranty. 

    They are not under warranty for racing applications, and there is no warranty on wear parts. (Uniball/Misalignments). 

    Select options
  • Clevis Tie Rod ENDS 1000/Turbo

    $45.00$90.00

    These are the ENDS ONLY

    These only fit 1000/ Turbo models

    Select options
  • Receiver Hitch Plate for Factory Replacement

    $145.00

    This receiver hitch plate is for anyone that isn’t planning on running a bumper, or is running bumper that requires the use of a factory shaped radius rod plate. 

    It is just a direct replacement of the factory radius rod plate with an added receiver hitch.

    This only comes in black.

    Material Specs:

    1/4″ thick HRPO steel. 

    Receiver protrusion for all variations is 5-15/16″

    All variations accepts standard 2″ receiver with 5/8″ pin

    Select options
  • 1K/Turbo-Rear Bumper (14-18 Model)

    $350.00$400.00

    This Listing is for 1k/turbo 14-18 Model only!
    It WILL NOT fit a 2019-up model rzr. 

    This bumper comes with a rear radius plate (steel-powdered black) and all hardware needed to install. Made from 1.75 x .120 Wall Steel

     CHECK OUT our Additional Bumper Add Ons and Upgrades Below!

    Select options
  • 1K/TURBO- Receiver Hitch Plate for L&W Bumper

    $145.00

    This is a replacement for the steel or billet radius plates that are used in correspondence with an L&W Bumper.

    They come in black only.

    Material Specs:

    1/4″ thick HRPO steel. 

    Receiver protrusion for all variations is 5-15/16″

    All variations accepts standard 2″ receiver with 5/8″ pin

    Select options
  • Race Style REAR Bumper (2019-2023)

    $325.00$375.00

    This listing is for 1K/TURBO models only.

    This bumper comes with a rear radius plate (steel-powdered black) and all hardware needed to install. 

    Made from 1.75 x .120 Wall Steel

    CHECK OUT our Additional Bumper Add Ons and Upgrades Below!

     

     

     

    Select options
  • RZR XP TURBO/ TURBO S- SIDE VENT COVERS

    $80.00$205.00

    POLARIS RZR XP TURBO/ TURBO S- SIDE VENT COVERS

    Made from 18ga steel


    Comes with all necessary hardware. Drilling requiried


    Add some bling to your XP Turbo while also protecting the frog skin


    Can be bought as 2pc (outside only/Inside Only) or 4 pc(inside and outside)

     

    • Mesh will be black *

    ONLY FIT ’17 and up models!

    Select options

Click here to assign a widget for this area.