Category: RZR 1000
RZR 1000
Showing 1–40 of 44 results
-
Seat Lowering Bases
$80.00 – $125.00Select optionsINTRODUCING THE L&W SEAT LOWERING BASE!-Easier to Install-Uses Stock Slider-Slider Plate integrated-Harness 5th Point Mount-Lowers 2”-Reclines 5.2 degrees- Powder Coated Black
- HARDWARE KIT IS INCLUDED, you do not need to purchase it separately.
- There are pieces you need from the original seat base.
- Works with MOST aftermarket seats. (L&W is not responsible for fitment issues when using aftermarket seats)
- ALSO please note that since these recline the seat 5.2 degrees you will not be able to slide the seat all the way back, causing you to lose some leg room.
-
1K/TURBO/RS1- Rear Radius Rods
$240.00 – $465.00Select optionsTHIS LISTING IS FOR 1K/TURBO/RS1 MODELS ONLY.
The lowers are High clearance and always come Direct Bolt.
The Direct Bolt Uppers come with no adjustment as they are direct fit.
The 1 Heim Uppers come with a Right hand heim on one end of each rod for adjustability if needed.
The 2 Heim Uppers come with both a Left and Right Hand heim on each end of the rod for adjustability if needed.
*Adjustable uppers are usually necessary to correct any camber issues that you may have or experience on your machine. Most times if you plan to change tender springs, or if you are running a bigger set up (portals, lifts, changing ride height most times will cause +/- camber that you will need to correct with adjustable uppers.)
Includes all misalignment spacers needed for install.
They are 6061 Aluminum, and made in the USA.
These Radius Rods hold a Lifetime Warranty.
-
1K/Turbo Tie Rods – Factory Style
$189.00 – $290.00Select optionsThese Tie Rods Fit Polaris RZR 1000 and Turbo
Specs on the Rods:
These are factory style ball and socket tie rods.
This listing is for a SET
6061 Aluminum.
Made in America
Lifetime Warranty on rod itself.
Comes with Spindle Ends (You do not need to purchase the spindle ends separate from this kit, unless you need a replacement spindle end)
To determine whether you have M14 or M16, please measure the ends of you factory tie rods (the side that screws into the rack). If the end is less the 1/2″ you will need M14, if it is over 1/2″ you will need M16. The turbo model usually takes M16 ( measuring is recommended ), the 1000 model is not consistent and will need to be measured. **2016 Turbo will always be M14**
Factory ends are not warrantied, only the tie rod itself.
Specs for HD Rebuild-able Tie Rod Ends:
Fully rebuildable
Comes assembled with grease ready for installation Compatible with all L&W tie rods plus many others Starts with heat treated 4140 Black oxide finished
100 percent made in USA
This product holds an 18 month warranty
Options:
1) M14x1.5 rack side by m14x1.5 tie rod side. 5-5/8″ total length. (4″ length from rack to end of Jam nut)
2) M16x1.5 rack side by m14x1.5 tie rod side. 5-5/8″ total length. (4″ length from rack to end of jam nut)
https://landwfab.com/product-category/rzr-parts/tie-rods/
https://www.facebook.com/landwfab/
-
High Clearance A Arms 1K/Turbo (2017- Current Models)
$300.00 – $725.00Select optionsThese High Clearance A Arms are raw material.
1 1/4 tubing .120 wall DOM.
L and W offers a life time warranty on bending and breaking the A arms.
DOES NOT COME TAPPED FOR GREASE FITTINGS.
Please select raw in the color options if you do not want powder coating.
These now take 17 and up model bushings.
If you have a 14-16 model, you will need to purchase 17 & up model bushings.
Bushing Sold Separately. Please see link in description for bushings.
-
Aftermarket Mount Plate for Milwaukee Packout
$120.00Add to cartMilwaukee Packout mount plate:
Works with all Polaris RZR XP1000/Turbo, Turbo S. Also works with Highlifter editions.
Made with 10ga HRPO steel.
Easily installed/removed with no tools using the supplied hardware.
Mount is slotted for different configurations of boxes to maximize trunk room for coolers.
Most coolers under 26qt will still fit. -
Clevis Style Tie Rods (1K/Turbo)
$189.00Select optionsThese are clevis style tie rods (heavy duty).
This listing is for a SET
Tie Rod ends are not consistent across all models or years. Please make sure to measure the rack end of stock tie rods to be sure of which size you need.
To determine what size you need, please measure the end of your tie rod that screws into the rack, if the measurement is less the 1/2″ you will need M14, if it is more then 1/2″ you will need M16.
These tie rods are made to work well for a racing style application.
6061 Aluminum.
Made in America
Life Warranty.
Ends are not warrantied, only the tie rod itself.
-
1.75″ Forward 1K/Turbo High Clearance A Arms (Full Kit)
$625.00 – $725.00Select optionsL and W offers a life time warranty on bending and breaking the A arms.
Will NOT work with 6+1 or 5+2 Offset Wheels, UNLESS you are running either a steering stop or 1inch wheel spacers.
DOES NOT COME TAPPED FOR GREASE FITTINGS
Please select raw in the color options if you do not want powder coating.
These now take 17 and up model bushings.
If you have a 14-16 model, you will need to purchase 17 & up model bushings.
Bushing Sold Separately. Please see link in description for bushings.
PLEASE ALLOW 7-10 DAYS on BACK-ORDER PRODUCTS or POWDER COATING
-
1K/TURBO- Race Style Winch Bumper (19-Current)
$300.00 – $350.00Select optionsThis listing is for 1K/TURBO models only.
(19-Current models)
This bumper comes with all mounting winch plates and hardware needed to install.
(DOES NOT INCLUDE FAIRLEAD)
Setup to Mount Standard 3,500 lb to 6,000 lb winch’s. (Black Ops preferred, but will take other winches brands as well)
Wide Spool Winches DO Fit In This Bumper
These bumpers use a 6 inch fairlead.
-
Tree Kicker Bolt Kit
$40.00 – $85.00Select optionsThis tree kicker bolt kit is for 2 or 4 seater L&W tree kickers.
(1K/TURBO/TURBO-S) 2 seater set comes with 4 L bolts.
(1K/TURBO/TURBO-S) 4 seater set comes with 6 L bolts.
(PRO XP) 2 seater set comes with 6 frame pins.
(PRO XP) 4 seater set comes with 8 frame pins.
This is just a replacement kit.
For new tree kickers, click the link below.
If you are looking for new tree kickers please click here- https://landwfab.com/?s=TREE+KICKERS&product_cat=0&post_type=product
-
Keller Ball Joint
$130.00 – $510.00Select optionsIf you are needing ball joints for a full set (4) of A Arms, please choose a set of 4.
If you are needing them for Uppers, choose a set of 2.
If you are needing them for Lowers, choose a set of 2.
The Mega Ball Joints are used for our mega ball joint a arms. The will not fit a regular a arm.
These ball joints are for rzr only. They do not fit a general.
These ball joints have a hardened body and stem. Stem is built from AMERICAN made 4340 and hardened for maximum strength and wear resistance. Adjustable and greasable with a replaceable boot.
-
Cooler Mount for 1k/ Turbo
$100.00Add to cartCooler Mounts:
Fits a 1K/Turbo (For Turbo S, please see Turbo S Listing)
1. Works with All RZR XP including highlifter edition
2. Uses eye bolt Grip mount
3. All hardware included
4. Made from 3/16 HRPO
5. Fully adjustable to fit over 30 different cooler models including these top models:
i) YETI Tundra 35
ii) RTIC 20
iii) YETI 20
iv) Ozark 26
v) NICE 26IS NOT COMPATIBLE WITH POLARIS OR PELICAN COOLERS.
6. Comes powder coated black
[video width="1920" height="828" mp4="https://landwfab.com/wp-content/uploads/2020/10/RZR-XP-TURBO-COOLER-MOUNT.mp4"][/video] -
1K/Turbo Rear Bumper (2019-Current)
$350.00 – $400.00Select optionsThis listing is for 1K/TURBO models only.
This bumper comes with a rear radius plate (steel-powdered black) and all hardware needed to install.
Made from 1.75 x .120 Wall Steel
CHECK OUT our Additional Bumper Add Ons and Upgrades Below!
-
1K/TURBO- 2019 to Current Front Winch Bumper
$450.00 – $500.00Select optionsThis listing is for 19-CURRENT 1K/TURBO MODELS ONLY.
This bumper comes with all mounting winch plates and hardware needed to install.
(DOES NOT INCLUDE FAIRLEAD)
Setup to Mount Standard 3,500 lb to 6,000 lb winch’s. (Black Ops preferred, but will take other winches brands as well)
Wide Spool Winches DO Fit In This Bumper
These bumpers use a 6 inch fairlead.
WITH BROW: LOOPS AROUND HEADLIGHTS
NO BROW: UNDER HEADLIGHTS
-
Full Windshields for L&W Cages
$260.00 – $300.00Select optionsThese windshields are made to fit L&W Production cages ONLY!
Windshields are made from 3/16 polycarbonate with MARGARD coating.
The maragard coating makes it scratch resistant. (Resistant not proof)
Comes complete with all hardware for easy installation
Made in the USA
-
(MEGA) 1.75″ Forward High Clearance A Arms- 1K/TURBO
$625.00 – $725.00Select optionsTHIS LISTING IS FOR A FULL KIT.
L and W offers a life time warranty on bending and breaking the A arms.
These A Arms are constructed for Mega Ball Joints ONLY.
Will NOT work with 6+1 or 5+2 Offset Wheels.
Please select raw in the color options if you do not want powder coating.
Our A Arms now require 17+ model bushings.
If you have a 14-16 you will need to purchase the bushing kit for the 17+ model.
Bushing Sold Separately. Please see link in description for bushings.
PLEASE ALLOW 7-10 DAYS on BACK-ORDER PRODUCTS or POWDER COATING
-
Gordon Cage- 1K/Turbo/Turbo S- 4 Seater
$2,000.00Select optionsGordon Standard is a 6″ Chop
Gordon Low is a 8″ Chop
If you would like to purchase a windshield to fit this cage please click here!
Currently we are only shipping cages RAW. Powder Coated options are pick up only.
- Price includes Aluminum Roof.
- Cage DOES NOT come standard with grab bars or intrusion bars. Those must be added for an additional charge.
- Please allow 1-3 business days for add ons and 10-15 business days for powder coating.
- Please indicate color of cage and roof, if you chose the powder coat option.
(See shipping details in Additional Info below!)
-
Seat lowering Base Hardware Kit
$15.00 – $30.00Select optionsThis Listing is for a SET for TWO seat lowering base hardware kits or for a SINGLE seat base.
This is not required with the purchase of a new set of bases.
This is only a replacement kit.
This hardware kit is a replacement for RZR as well as General seat lowering bases.
-
Aftermarket Snap In Grill with Light Bar
$185.00Select optionsComes with Light Bar (does not include wiring harness)
Options for outline color and L&W logo
The grill mesh will always be black
Fitment:
Turbo S
19-current models 1K/Turbo
*NOTE: THIS GRILL WILL NOT WORK WITH THE FACTORY POLARIS BUMPER WITHOUT MAKING SLIGHT MODIFICATIONS TO FIT.*
-
1K/Turbo/Turbo S- 2 Seater Cage
$1,150.00 – $1,350.00Select optionsCages are made out of .120 DOM – 1.75″ in diameter.
These cages are shipped LTL and carry an additional shipping charge. (By purchasing this listing, you are agreeing to pay any and all shipping charges which are additional and are not included in the price on this listing. Shipping can range anywhere from $600-$1500 per cage. Up to date charges for specific destination will be charged. You will be contacted within 24 hours of purchase to arrange shipping quote and payment.)
Cage Includes aluminum roof
Currently we are only shipping cages RAW. Powder Coated options are pick up only.
Cage DOES NOT come standard with grab bars. Those must be added for an additional charge.
Please allow 1-3 business days for add ons and 7-10 business days for powder coating.
Please indicate color of cage and roof, if you chose the powder coat option.
-
1K/Turbo-Rear Bumper (14-18 Model)
$350.00 – $400.00Select optionsThis Listing is for 1k/turbo 14-18 Model only!
It WILL NOT fit a 2019-up model rzr.This bumper comes with a rear radius plate (steel-powdered black) and all hardware needed to install. Made from 1.75 x .120 Wall Steel
CHECK OUT our Additional Bumper Add Ons and Upgrades Below!
-
Receiver Hitch Plate for Factory Replacement
$145.00Select optionsThis receiver hitch plate is for anyone that isn’t planning on running a bumper, or is running bumper that requires the use of a factory shaped radius rod plate.
It is just a direct replacement of the factory radius rod plate with an added receiver hitch.
This only comes in black.
Material Specs:
1/4″ thick HRPO steel.
Receiver protrusion for all variations is 5-15/16″
All variations accepts standard 2″ receiver with 5/8″ pin
-
1K/TURBO- Receiver Hitch Plate for L&W Bumper
$145.00Select optionsThis is a replacement for the steel or billet radius plates that are used in correspondence with an L&W Bumper.
They come in black only.
Material Specs:
1/4″ thick HRPO steel.
Receiver protrusion for all variations is 5-15/16″
All variations accepts standard 2″ receiver with 5/8″ pin
-
Race Style REAR Bumper (2019-Current)
$325.00 – $375.00Select optionsThis listing is for 1K/TURBO models only.
This bumper comes with a rear radius plate (steel-powdered black) and all hardware needed to install.
Made from 1.75 x .120 Wall Steel
CHECK OUT our Additional Bumper Add Ons and Upgrades Below!
-
1K/Turbo/RS1- Steel HD Trailing Arms
$825.00 – $875.00Select optionsFITMENT: 1K/TURBO/RS1
These Steel HD Trailing Arms are built from 1″ 1/2 x 3 3/16 Rectangle Tubing.
You may choose the color of the Trailing arm itself, however the brake line logo bracket comes powder coated black.
These trailing arms hold a lifetime warranty.
They are not under warranty for racing applications, and there is no warranty on wear parts. (Uniball/Misalignments).
-
Offroad Rugged X-Grip Phone / Tablet Mount for Roll Cage
$65.33 – $125.85Select options- American made
- Comes with Ram Mounts X-Grip
- Each clamp is 1/2″ thick
- These will fit 1.75″ tubing
- Great way to mount your phone to any tubing
- Made from 6061-T6 Billet Aluminum
Large Ram mount phone holder will except a phone width from 1.75″ to 4.50″
Small Ram mount tablet holder will except a tablet width from 2.50″ to 5.75″
Large Ram mount tablet holder will except a tablet width from 6.25″ to 8.10″ and 10.25″ long
-
Receiver Hitch Add On Plate
$145.00Add to cartThis is the receiver hitch for anyone that currently has an L and W radius rod plate steel/billet that wants to add a receiver hitch.
It can be used with our bumpers as well.
Only comes in black.
Material Specs:
1/4″ thick HRPO steel.
Receiver protrution for all variations is 5-15/16″
All variations accepts standard 2″ receiver with 5/8″ pin
-
2014-2018 Front Winch Bumper 1K/TURBO
$450.00 – $500.00Select options2014-2018 Front Winch Bumper 1K/TURBOThis bumper comes with all mounting winch plates and hardware needed to install.
(DOES NOT INCLUDE FAIRLEAD)
This bumper comes (WITH BROWS) AS PICTURED ABOVE ONLY. MEANING IT LOOPS AROUND THE HEADLIGHTS.
Setup to Mount Standard 3,500 lb to 6,000 lb winch’s. (Black Ops preferred, but will take other winches brands as well)
Wide Spool Winches DO Fit In This Bumper
These bumpers use a 6 inch fairlead.
-
Mega Ball Joint A Arms-Standard (1K/Turbo)
$625.00 – $725.00Select optionsThese A Arms are constructed for Mega Ball Joints ONLY.
These High Clearance A Arms are raw material.
1 1/4 tubing .120 wall DOM.
L and W offers a life time warranty on bending and breaking the A arms.
DOES NOT COME TAPPED FOR GREASE FITTINGS.
Please select raw in the color options if you do not want powder coating.
These now take 17 and up model bushings.
If you have a 14-16 model, you will need to purchase 17 & up model bushings.
