0$0.00

No products in the cart.

Products

Showing 1–40 of 192 results

  • Seat Lowering Bases

    $80.00$125.00
    INTRODUCING THE  L&W SEAT LOWERING BASE! 
     
    -Easier to Install
    -Uses Stock Slider
    -Slider Plate integrated
    -Harness 5th Point Mount
    -Lowers 2”
    -Reclines 5.2 degrees
    • Powder Coated Black 
    • HARDWARE KIT IS INCLUDED, you do not need to purchase it separately.
    • There are pieces you need from the original seat base. 
    • Works with MOST aftermarket seats. (L&W is not responsible for fitment issues when using aftermarket seats)
    • ALSO please note that since these recline the seat 5.2 degrees you will not be able to slide the seat all the way back, causing you to lose some leg room. 
     
    Select options
  • 1K/TURBO/RS1- Direct Bolt Radius Rods

    $240.00$675.00

    THIS LISTING IS FOR 1K/TURBO/RS1 MODELS ONLY.

    This listing is for the Direct Bolt Radius Rods.

    The lowers are High clearance. 

    Includes all spacers needed for install. 

    They are 6061 Aluminum, and made in the USA. 

    These Radius Rods hold a Lifetime Warranty. 

    Select options
  • 1K/Turbo Tie Rods – Factory Style

    $189.00$290.00

    These Tie Rods Fit Polaris RZR 1000 and Turbo

    Specs on the Rods:

    These are factory style ball and socket tie rods. 

    This listing is for a SET

    6061 Aluminum. 

    Made in America

    Lifetime Warranty on rod itself.

    Comes with Spindle Ends (You do not need to purchase the spindle ends separate from this kit, unless you need a replacement spindle end) 

    To determine whether you have M14 or M16, please measure the ends of you factory tie rods (the side that screws into the rack). If the end is less the 1/2″ you will need M14, if it is over 1/2″ you will need M16. The turbo model usually takes M16 ( measuring is recommended ), the 1000 model is not consistent and will need to be measured. **2016 Turbo will always be M14**

     

    Factory ends are not warrantied, only the tie rod itself. 

     

    Specs for HD Rebuild-able Tie Rod Ends:

    Fully rebuildable

    Comes assembled with grease ready for installation Compatible with all L&W tie rods plus many others Starts with heat treated 4140 Black oxide finished

    100 percent made in USA

    This product holds an 18 month warranty

    Options:

    1) M14x1.5 rack side by m14x1.5 tie rod side. 5-5/8″ total length. (4″ length from rack to end of Jam nut)

    2) M16x1.5 rack side by m14x1.5 tie rod side. 5-5/8″ total length. (4″ length from rack to end of jam nut)

    https://landwfab.com/product-category/rzr-parts/tie-rods/

    https://www.facebook.com/landwfab/

     

    Select options
  • High Clearance A Arms 1K/Turbo (2017- Current Models)

    $300.00$725.00

    These High Clearance A Arms are raw material.

    1 1/4 tubing .120 wall DOM. 

    L and W offers a life time warranty on bending and breaking the A arms. 

    DOES NOT COME TAPPED FOR GREASE FITTINGS. 

    Please select raw in the color options if you do not want powder coating. 

    These now take 17 and up model bushings.

    If you have a 14-16 model, you will need to purchase 17 & up model bushings.

    Bushing Sold Separately. Please see link in description for bushings.

     

    Select options
  • Aftermarket Mount Plate for Milwaukee Packout

    $120.00

    Milwaukee Packout mount plate:

    Works with all Polaris RZR XP1000/Turbo, Turbo S. Also works with Highlifter editions.

    Made with 10ga HRPO steel.
    Easily installed/removed with no tools using the supplied hardware.
    Mount is slotted for different configurations of boxes to maximize trunk room for coolers.
    Most coolers under 26qt will still fit.

    Add to cart
  • A Arm Bushing

    $60.00$129.00

    Bushing by Performance Side X Side

     

    These bushings WILL NOT fit the s models, including the Turbo S. They will only fit the 1000 and Turbo models. 

     

    They do not fit a general

    Select options
  • Radius Plate- 1K/TURBO/RS1

    $115.00$140.00

    This radius plate has a lifetime warranty.

    Made from 6061 Aluminum.

    We make this product in Temple, Ga. 

    1K/ Turbo/ RS1

    DOES NOT WORK WITH FACTORY BUMPER.

    https://landwfab.com/product-category/rzr-parts/radius-rods/

    https://www.facebook.com/landwfab/

    Select options
  • Heim Replacements

    $15.00

    This Listing is for 5/8 & 3/4 Heims.

    These are replacement Heims only, they do not carry any warranty as they are considered a wear part.

    We recommend keeping them greased with a non water based lubricant for a longer lasting use. 

    WE OFFER BOTH LEFT AND RIGHT HAND THREADS.

    PLEASE READ FITMENT BELOW IF NEEDING TO KNOW WHICH THREAD TO PURCHASE FOR L&W PRODUCTS.

    Select options
  • Uniball and Snap Ring Replacements

    $8.00$25.00

    Uniball and Snap ring replacements for L&W Radius Rods and Trailing Arms.

    PLEASE MEASURE THE INSIDE DIAMETER OF YOUR CURRENT UNIBALL TO MAKE SURE YOU GET THE CORRECT REPLACEMENT FOR YOUR PARTS. (L&W is NOT responsible for knowing the size Uniball needed for your product, as some may vary.)

    These are considered wear items and are not covered under warranty claims. 

    We recommend using a NON water-based lubricant on these for longer lasting use. 

     

    SEE FITMENTS BELOW

    Select options
  • Clevis Style Tie Rods (1K/Turbo)

    $189.00

    These are clevis style tie rods (heavy duty).

    This listing is for a SET

    Tie Rod ends are not consistent across all models or years. Please make sure to measure the rack end of stock tie rods to be sure of which size you need.

    To determine what size you need, please measure the end of your tie rod that screws into the rack, if the measurement is less the 1/2″ you will need M14, if it is more then 1/2″ you will need M16.

    These tie rods are made to work well for a racing style application. 

    6061 Aluminum. 

    Made in America

    Life Warranty. 

    Ends are not warrantied, only the tie rod itself. 

     

    Select options
  • Aluminum Drink Carrier

    $145.00

    Made from  Aluminum

    Mounts on T-Bar 

     

    Add to cart
  • Honda Talon Radius Rods (R Edition)

    $240.00$465.00

    Honda Talon Radius Rods ( R EDITION ONLY) 

    These Radius Rods are made out of 6061 Aluminum

    The raw option is a billet finish 

    Lifetime Warranty on non-wear parts

    Made in the USA 

    Free Shipping 

     

    Select options
  • 1.75″ Forward 1K/Turbo High Clearance A Arms (Full Kit)

    $625.00$725.00

    L and W offers a life time warranty on bending and breaking the A arms.

    Will NOT work with 6+1 or 5+2 Offset Wheels, UNLESS you are running either a steering stop or 1inch wheel spacers. 

    DOES NOT COME TAPPED FOR GREASE FITTINGS

    Please select raw in the color options if you do not want powder coating.

    These now take 17 and up model bushings.

    If you have a 14-16 model, you will need to purchase 17 & up model bushings.

    Bushing Sold Separately. Please see link in description for bushings.

    PLEASE ALLOW 7-10 DAYS on BACK-ORDER PRODUCTS or POWDER COATING

    Select options
  • Spindle End for Tie Rods

    $20.00$30.00

    This is a REPLACEMENT spindle end for tie rods. 

    If you have just purchased our tie rods, the spindle end will come with them. 

    This is just a replacement piece. 

    Select options
  • 1K/TURBO- Race Style Winch Bumper (19-Current)

    $300.00$350.00

    This listing is for 1K/TURBO models only.

    (19-Current models)

    This bumper comes with all mounting winch plates and hardware needed to install.

    (DOES NOT INCLUDE FAIRLEAD)

    Setup to Mount Standard 3,500 lb to 6,000 lb winch’s. (Black Ops preferred, but will take other winches brands as well)

    Wide Spool Winches DO Fit In This Bumper

    These bumpers use a 6 inch fairlead.

     

    Select options
  • Direct Bolt Radius Rods -Turbo S

    $265.00$490.00

    PLEASE ALLOW 7-10 DAYS on BACK-ORDER PRODUCTS or POWDER COATING

    Turbo S Direct Bolt Radius Rods

    Made from Billet Aluminum. 

    Includes all spacers needed for install.

    Does not include Turbo S Radius plate, to purchase a radius plate click here.

     

    Select options
  • Tree Kicker Bolt Kit

    $40.00$85.00

    This tree kicker bolt kit is for 2 or 4 seater L&W tree kickers. 

    (1K/TURBO/TURBO-S) 2 seater set comes with 4 L bolts.

    (1K/TURBO/TURBO-S) 4 seater set comes with 6 L bolts.

    (PRO XP) 2 seater set comes with 6 frame pins. 

    (PRO XP) 4 seater set comes with 8 frame pins.

    This is just a replacement kit. 

    For new tree kickers, click the link below. 

     

    If you are looking for new tree kickers please click here- https://landwfab.com/?s=TREE+KICKERS&product_cat=0&post_type=product

    http://facebook.com/landwfab

    Select options
  • Honda Talon Radius Rods (X Model)

    $240.00$465.00

    Honda Talon Radius Rods ( X EDITION ONLY) 

    These Radius Rods are made out of 6061 Aluminum

    The raw option is a billet finish 

    Made in the USA 

    Free Shipping 

    Select options
  • Sway Bar Links

    $100.00

    PLEASE ALLOW 7-10 DAYS on BACK-ORDER PRODUCTS or POWDER COATING

     

    Made of 6061

    Add to cart
  • Keller Ball Joint

    $130.00$510.00

    If you are needing ball joints for a full set (4) of A Arms, please choose a set of 4. 

    If you are needing them for Uppers, choose a set of 2. 

    If you are needing them for Lowers, choose a set of 2.

     

    The Mega Ball Joints are used for our mega ball joint a arms. The will not fit a regular a arm.

    These ball joints are for rzr only. They do not fit a general. 

     These ball joints have a hardened body and stem. Stem is built from AMERICAN made 4340 and hardened for maximum strength and wear resistance. Adjustable and greasable with a replaceable boot.

    Select options
  • Cooler Mount for 1k/ Turbo

    $100.00

    Cooler Mounts:

    Fits a 1K/Turbo (For Turbo S, please see Turbo S Listing)

    1. Works with All RZR XP including highlifter edition
    2. Uses eye bolt Grip mount
    3. All hardware included
    4. Made from 3/16 HRPO
    5. Fully adjustable to fit over 30 different cooler models including these top models:
       i) YETI Tundra 35
      ii) RTIC 20
      iii) YETI 20
      iv) Ozark 26
      v) NICE 26

    IS NOT COMPATIBLE WITH POLARIS OR PELICAN COOLERS.
    6. Comes powder coated black

     

    [video width="1920" height="828" mp4="https://landwfab.com/wp-content/uploads/2020/10/RZR-XP-TURBO-COOLER-MOUNT.mp4"][/video]
    Add to cart
  • Turbo S Tie Rods

    $300.00

    Turbo S Tie Rods: 

    This listing is for a SET

    Comes with spindle ends.

    6061 Aluminum. 

    Made in America

    Lifetime Warranty on the Tie Rod itself.

    Factory ends are not warrantied, only the tie rod itself. 

     

    Specs for HD Rebuild-able Tie Rod Ends:

    Fully rebuild-able

    Comes assembled with grease ready for installation Compatible with all L&W tie rods plus many others Starts with heat treated 4140 Black oxide finished

    100 percent made in USA

    This product holds an 18 month warranty

    Select options
  • Seat Lowering Bases for General

    $80.00$125.00
     

    -Easier to Install
    -Uses Stock Slider
    -Slider Plate integrated 
    -Harness 5th Point Mount 
    -Lowers 2” 
    -Reclines 5.2 degrees

    • Powder Coated Black 
    • HARDWARE KIT IS INCLUDED, you do not need to purchase it separately.
    • There are pieces you need from the original seat base. 
    • Works with MOST aftermarket seats. (L&W is not responsible for fitment issues when using aftermarket seats)
    • ALSO please note that since these recline the seat 5.2 degrees you will not be able to slide the seat all the way back, causing you to lose some leg room. 

    FITMENT:

    These WILL NOT work on the passenger side seat without cutting some of the plastics behind the seat so that you may slide the base all the way back for it to latch correctly.

     
    Select options
  • Warranty Shipping

    $20.00

    Please do not pay this warranty shipping until you have been contacted by a member of our customer service team and you warranty has been approved.

    If you have been sent this link by a member of our team, please click add to cart and continue with your shipping payment.

    Add to cart
  • 1K/Turbo- 2 Seater Tree Kickers

    $475.00$525.00

    This listing is for a set (driver and passenger) of 2 seater tree kickers.

    Model fitment: 1K/Turbo

    American Made. 

    Select options
  • 1K/Turbo Rear Bumper (2019-Current)

    $350.00$400.00

    This listing is for 1K/TURBO models only.

    This bumper comes with a rear radius plate (steel-powdered black) and all hardware needed to install. 

    Made from 1.75 x .120 Wall Steel

    CHECK OUT our Additional Bumper Add Ons and Upgrades Below!

    Select options
  • L&W Sak- It Scrap Sak

    $38.00

    These are the Sak-It Brand Scrap Sak’s with our L&W Logo.

    You can only get these here at landwfab.com

    Don’t leave your trash junking up your ride, when you can Sak-It!

    Add to cart
  • High Clearance Talon (R) A Arms

    $250.00$300.00

    These A Arms are for the R edition only.

    They are made from 1 1/4 inch tubing / 120 DOM

    We currently only offer the lowers for the R model.

    They take the factory ball joints

    They do not use the factory bushings.

    Each price includes the bushing you will need to run these A Arms

    These are Non- Adjustable

    They are factory offset

    These A Arms will have up to 3.5 inches more clearance

    Lifetime Warranty

    Made in the USA

    Select options
  • 1K/TURBO- 2019 to Current Front Winch Bumper

    $450.00$500.00

    This listing is for 19-CURRENT 1K/TURBO MODELS ONLY.

    This bumper comes with all mounting winch plates and hardware needed to install.

    (DOES NOT INCLUDE FAIRLEAD)

    Setup to Mount Standard 3,500 lb to 6,000 lb winch’s. (Black Ops preferred, but will take other winches brands as well)

    Wide Spool Winches DO Fit In This Bumper

    These bumpers use a 6 inch fairlead. 

     

    WITH BROW: LOOPS AROUND HEADLIGHTS

    NO BROW: UNDER HEADLIGHTS

     

    Select options
  • PRO XP Tie Rods

    $189.00$240.00

    These tie rods are for the Pro XP.

    They have a lifetime warranty. 

    Factory ends are not warrantied, only the tie rod itself. 

     

    Specs for HD Rebuild-able Tie Rod Ends:

    Fully rebuild-able

    Comes assembled with grease ready for installation Compatible with all L&W tie rods plus many others Starts with heat treated 4140 Black oxide finished

    100 percent made in USA

    This product holds an 18 month warranty

     

    https://www.facebook.com/landwfab/

    Select options
  • Cooler Mount for Turbo S

    $100.00

    Cooler Mounts:

    This listing is for TURBO S ONLY

     

    Cooler Mount (Factory Cage) Specs:

    1. Works with All Turbo S with factory cage
    2. Made from 3/16 HRPO
    3. Comes with all hardware needed
    4. Fully adjustable to fit over 30 different cooler models including these top models:
      i) YETI Tundra 35
      ii) RTIC 20
      iii) YETI 20
      iv) Ozark 26
      v) NICE 26

    NOT COMPATIBLE WITH PELICAN OR POLARIS COOLERS
    5. Comes powder coated black

    [video width="1920" height="828" mp4="https://landwfab.com/wp-content/uploads/2020/10/TURBO-S-COOLER-MOUNT-FACTORY-CAGE.mp4"][/video]

    Cooler Mount (Aftermarket Cage) Specs:

    1. Works with most Turbo S with aftermarket cage that doesn’t utilize rear support bars.
    2. Made from 3/16 HRPO
    3. Comes with all hardware
    4. Fully adjustable to fit over 30 different cooler models including these top models:
      i) YETI Tundra 35
      ii) RTIC 20
      iii) YETI 20
      iv) Ozark 26
      v) NICE 26

    NOT COMPATIBLE WITH PELICAN OR POLARIS COOLERS
    5. Comes powder coated black

    [video width="1920" height="828" mp4="https://landwfab.com/wp-content/uploads/2020/10/TURBO-S-COOLER-MOUNT-AFTERMARKET-CAGE.mp4"][/video]
    Select options
  • TURBO S- 2 Heim Radius Rods

    $265.00$490.00

    THIS LISTING IS FOR TURBO S MODELS ONLY.

    The Upper Radius Rods in this kit have both a Left hand and Right hand heim on each end for adjustability if needed. 

    The Lower Radius Rods will be direct bolt on.

    Includes all spacers needed for install. 

    PLEASE NOTE THAT IF YOU HAVE GEN3 SUPERATV PORTALS YOU WILL NEED TO PURCHASE THE UPPER ADJUSABLE RADIUS RODS (1 HEIM OR 2 HEIM) in order for your suspension to have enough room to travel without busting the portal bracket ear. 

    They are 6061 Aluminum, and made in the USA. 

    These Radius Rods hold a Lifetime Warranty.

     

    Select options
  • Turbo S- Standard A-Arms

    $350.00$750.00

    These Turbo S Arms are made from 1.5″ tubing, 120 wall DOM, and have some 1.25 bracing 

    Uses the factory bushings and ball joints.

    They are covered by a lifetime warranty and are made in the USA. 

    Select options
  • Honda Talon Winch Mount

    $85.00

    This winch mount comes powder coated black. 

    It is made for the R and the X edition that have the stock bumper. 

    They can be used with 3500, 4500, and 5000 lb winch. 

    The photos shown are a 4500 lb winch. 

    Made in the USA

    Lifetime Warranty 

    Free Shipping 

     

    Select options
  • Seat Lowering Base Set (800/900 Models)

    $125.00

    This listing is for our seat lowering base set. 

    We have a lot of questions regarding if it will work with a 800/900 model RZR.

    This seat lowering base will work with a 1000 seat placed in an 800/900 model.

    YOU WILL HAVE TO USE THE 1000 SLIDER IN ORDER FOR THE SLIDE TO WORK, IT WILL NOT WORK WITH THE 800/900 SLIDER.

    It WILL NOT work with the factory 800/900 seats. 

    Add to cart
  • Turbo S Radius Plate

    $115.00

    This radius plate has a lifetime warranty.

    Made from 6061 Aluminum.

    This will work with our Turbo S radius rods. 

    If you run a rear bumper, these will only work with L&W bumpers. 

    Add to cart
  • Reverse Light

    $85.00$110.00

    This Reverse Light will work with: Turbo S models 2018-2020 and 1k/Turbo Models 2019-2020.

    It comes with 12ft. of wire 

    5/10 rocker switch with fuse and relay 

    Select options
  • TURBO S- Front Winch Bumper

    $465.00$515.00

    This listing is for Turbo S models only.

     

    This bumper comes with all mounting winch plates and hardware needed to install.

    (DOES NOT INCLUDE FAIRLEAD)

    Setup to Mount Standard 3,500 lb to 6,000 lb winch’s. (Black Ops preferred, but will take other winches brands as well)

    Wide Spool Winches DO Fit In This Bumper

    These bumpers use a 6 inch fairlead. 

     

    WITH BROW: LOOPS AROUND HEADLIGHTS

    NO BROW: UNDER HEADLIGHTS

    Select options
  • PRO XP- 2 Heim Radius Rods

    $240.00$465.00

    THIS LISTING IS FOR PRO XP MODELS ONLY.

    The lowers are High clearance and always come Direct Bolt.

    The 2 Heim Uppers come with both a Left and Right Hand heim on each end of the rod for adjustability if needed. 

    *Adjustable uppers are usually necessary to correct any camber issues that you may have or experience on your machine.  Most times if you plan to change tender springs, or if you are running a bigger set up (portals, lifts, changing ride height most times will cause +/- camber that you will need to correct with adjustable uppers.) 

    Includes all misalignment spacers needed for install. 

    They are 6061 Aluminum, and made in the USA. 

    These Radius Rods hold a Lifetime Warranty.

    Select options
  • TURBO S- Race Style Winch Bumper

    $300.00$350.00

    This listing is for Turbo S models only.

    This bumper comes with all mounting winch plates and hardware needed to install.

    (DOES NOT INCLUDE FAIRLEAD)

    Setup to Mount Standard 3,500 lb to 6,000 lb winch’s. (Black Ops preferred, but will take other winches brands as well)

    Wide Spool Winches DO Fit In This Bumper

    These bumpers use a 6 inch fairlead.

    Select options